Asphalt mixing plant,Asphalt mixing plant manufacturer,AMP Manufacturer
Installation form: main unit is built up in modular and joined together with screws.
Operation conditions concerning production capacity:
① Altitude <1500m
② Average moisture content in aggregates≤5%
③ Optimum working temperature: 200C~500C
④ Power supply: 380V/50HZ
⑤ Cyclic period of mixing: 45~60sec
⑥ Mixing capacity of each batch: 700kg/batch
⑦ Aggregates: Clean and sized aggregates with moisture content <5%, dust content <1%, density ≥1.6t/m3. Needle-type or flat aggregate is not acceptable. Aggregates density, PH and hardness should conform to Material Regulations on Road Construction made by Ministry of Communication.
⑧ Mineral powder: Bag-packaged clean mineral powder or bulk fresh mineral powder, with moisture content less than 1%
⑨ Bitumen: Standard bitumen in conformity with national regulations
⑩ Fuel: Approved/ certified fuel with test report released by the testing authority. Fuel application should conform to relevant provisions specified in Burner’s Operation Introduction
Note: Production situations will change if real conditions of any abovementioned items are different with description.
Attention: Carefully read Operation Introduction prior to operating the machine.
Technical specifications for parts and accessories
一、 Supply system of cold aggregate
·Adopt modular design concept. Match aggregate belt machine as per customer’s requirement.
·Frequency-control feeder can adjust speed according to output setting and proportioning demand.
·High-quality rubber belt is used in the cold hopper, equipped with warning unit for feeding interruption.
·Aggregate belt machine/ feed belt machine is equipped with deviation corrector.
·Each hopper is equipped with grid on the top to resist incompliant stone material.
1.Supply system of cold aggregate (Part 1)
1.1Cold aggregate bin
Structure: Four-in-one
Volume of single hopper: 7.5m3
Feed width: 2.8m
Hopper quantity: 4pcs
1.2 Feed belt machine
Structure: Belt delivery/ primary distribution
Belt width: 500mm
Control: Frequency
Working capacity: 20T/H
Driving power: 2.2kw
Quantity: 4sets
1.3 Aggregate belt conveyor
Structure: Belt delivery
Working capacity: 60T/H
Belt width: 650mm
Driving power: 4kw
Quantity: 1set
1.4 Feed belt conveyor
Structure: Belt delivery
Working capacity: 56T/H
Belt width: 500mm
Inclination degree: <180
Driving power: 4kw
Quantity: 1set
二、 Baking& heating& lifting system
·Four-wheels friction drive
·Make heat preservation outside the drum to effectively reduce heat loss
·elevator with steel board
·Counterclockwise-rotation protector to prevent counterclockwise rotation upon power failure
·Lifting bucket is made of steel board via bending and welding. Enclose the complete bucket in a steel housing.
·Maintenance platform and ladder on the top, allowable dismantlement
·Access door at the bottom to regulate chain tension
1. Baking& heating& lifting system (Part 2)
2.1 Drying drum
Structure: Barrel, inclined, countercurrent
Driving type: Four-wheel friction drive
Working capacity: 56T/H (moisture content of aggregate≤3% at discharge temperature of 1600C)
Drum diameter: φ1300mm
Drum length: 6500mm
Driving power: 7.5KW×2
Inclination degree: 4.50
Temperature measurement: Thermal resistance measurement for stone temperature
Quantity: 1set
2.2 Main burner
Control mode: Proportion adjustment, according aggregate’s temperature changing adjust the air door and fuel quantity.
Fuel feeding ability: 600kg
Fuel style: 0# diesel
Fuel consumption: 6~7kg/t
Error Limit: ±90C( under stable condition of water content of the aggregate)
Blower power: 18.5KW
Oil pump power: 1.5KW
Air compressor: 7.5KW
Quantity: 1set
2.3 Diesel tank
Structure: Horizontal steel barrel
Max volume: 10M3 (1M3 diesel oil tank when using heavy oil)
Quantity: 1set
2.4 Hot-Aggregate elevator
Structure: bucket type of vertical lifting
Working capacity: 56t/h
Driving power: 7.5KW
Quantity: 1set
三、 Screening& metering system
·Professional vibration-screen design, reliable screening capacity
·Bin equipped with level indicator
·With discharge pipe for incompliant material and overflow pipe for compliant material
·Metering system measures force with detector. Signal directly inputs into electronic scale and is displayed by digital,with automatic correction and dynamic compensation functions.
2. Screening& metering system (Part 3)
3.1 Vibration screen
Structure: Inclined two-in-four distribution
Working capacity: 56t/h
Driving power: 5.5KW
3.2 Hot-aggregate bin
Structure: Full-enclosed, separated, square, steel, four-sections bin
Full volume: 7.5m3
Quantity: 1set
3.3 Aggregate-material metering
Structure: Three-points force measurement
Weighing capacity: 700kg
Static metering precision: ±0.5%
Quantity: 1set
3.4 Mineral powder metering
Structure: Three-points force measurement
Weighing capacity: 70kg
Static metering precision: ±0.25%
Quantity: 1set
3.5 Bitumen metering
Structure: Three-points force measurement
Weighing capacity: 70kg
Static metering precision: ±0.25%
Quantity: 1set
四、 Supply system for fresh powder and recovered powder
Powder storage& supply system comprises transition bin, impeller rotary valve feeder, spiral conveyor, powder elevator and etc.
4.Supply system for fresh powder and recovered powder (Part 4)
4.1 Powder silo
Capacity: 25 m3
Quantity: 1set
4.2 Spiral conveyor
Rated output: 12t/h
Driving power: 3kw
Quantity: 2sets(including conveyor for recovered powder)
4.3 Powder elevator
Rated output: 12t/h
Driving power: 3kw
Quantity: 2sets (including recovered powder)
4.4 Transition bin: Fresh powder 0.9m3,
recovered powder bin: 0.9m3
Feeding method: Vertical elevator
Quantity: 1set
4.5 Star-type discharge valve
Type: YJD-HX10
Working capacity: 10L/rotation
Impeller rotation speed: 24rpm
Driving power: 1.1KW
Quantity: 2sets
4.5 Mineral powder metering& spiral conveyor
Rated output: 15t/h
Driving power: 3kw
Quantity: 1set
五、 Mixing system
·Mixing blade and lining board made of friction-resistance material
·Synchronous twin-shaft rotary mixing system rotates materials in the mixer along mixing shaft cycle and axis. Material makes 3D rotation. The purpose is to ensure achieve mixing effect during mixing period.
5.Mixing system (Part 5)
5.1 Mixer
Structure: Twin horizontal shafts/ rotary mixing/ side-moving door
Mixing capacity: 700kg/batch
Driving power: 30KW
Cycle: 45~60sec
Quantity: 1set
六、 Dedusting system
·Square steel cabinet, impulse-air bag dedusting system
·2-stage protection for bag. First-stage protection is working temperature setting in thermo-detector. As measured temperature by sensor is higher than setting, cold-air valve in the air-in pipe opens automatically. On the second-stage protection, if temperature does not fall by cold-air valve, impulse controller will send signal to burner control cabinet to shut off power supply to burner.
6. Dust catching system (Part 6)
6.1 Cyclone dedustor (I-stage dedusting)
Structure: steel-typed barrel structure
Dedusting method: Centrifugal dust collection (Supply to hot-material elevator for mix)
Quantity: 1set
6.2 Bag dedustor (II-stage dedusting)
Structure: Square steel cabinet/ heat-preservation with asbestos and colored steel board
Dedusting method: Sectional impulse back-flushing by compressed air
Filtering area: 246m2
Powder discharge: ≤100mg/n.m3
Working temperature: 80~1300C
Power:3KW
Quantity: 1set
6.3 Star-type discharge valve
Type: YJD-HX10
Working capacity: 10L/rotation
Impeller rotation speed: 24rpm
Driving power: 1.1KW
6.4 Main draught fan
Structure: Steel centrifugal fan
Airflow: 34,550 m3/h
Full pressure: 2049pa
Driving power: 37kw
Quantity: 1set
Note: Too large moisture content and dust content of aggregate will serious affect performance of cyclone dedustor and bag dedustor.
七、Heat conductive oil heating system
·Connect heat conductive oil furnace, circulating oil pump, bitumen high-temperature tank, bitumen heat-preserved delivery pump and bitumen zero-position tank with heat conductive oil pipe, forming heat conductive oil heating system
·Heat conductive oil furnace equips automatic temperature-control oil burner. 0# diesel oil
·Recommend heat-preservation action for pipe after installation and debugging to avoid operator scalded, save fuel and improve heat efficiency.
7 Heat conductive oil heating system (Part 7)
7.1 Heat conductive oil furnace
Furnace type: YYW-350
Burner type: RL-44(Italy brand)
Rated heat efficiency: 350KW
Suitable fuel: 0# diesel oil
Driving power of burner: 0.45KW
Power of heat conductive oil circulating pump: 7.5 KW
Power of heat conductive oil filling pump: 1.1KW
Quantity: 1set
7.2 Bitumen high-temperature tank
Structure: Horizontal steel barrel/ heat-preservation with asbestos
Volume: 20m3
Heating method: Heat conductive oil
Quantity: 1set
Fittings: Pipe, valve and etc.
7.3 Bitumen drainage pond
Structure: Horizontal rectangle steel structure
Volume: 5m3
Heating method: Heat conductive oil
Quantity: 1set
Fittings: Pipe, valve and etc.
7.4 Bitumen delivery pump
Type: 3QGB80×2—36
Delivery flow rate: 15m3/h
Delivery lift: 60m
Driving power: 5.5KW
Quantity: 2sets
Note: Mentioned heating system does not contain heat conductive oil. (If Buyer requires it, please specify upon ordering.)
八、 Gas-circuit control system
8.Gas-circuit control system (Part 8)
8.1 Air compressor
Structure: Air-cooling
Exhaust quantity: 1.0m3/min*2
Working pressure: 0.7Mpa
Driving power: 7.5KW*2
Quantity: 2sets
8.2 Solenoid valve
Pressure range: 1.5~8kgf/cm2
Voltage range: AC187V~242V
Quantity: 1set
8.3 Relief valve
Pressure range: 0.5~8.5kgf/cm2
Quantity: 3pcs
8.4 Cylinder
Pressure range: 0.5~7kgf/cm2
Quantity: 1set
九、 Computer-controlled system
·PLC serves as central controller.
·User-friendly control interface facilitates operation and learning. It is convenient and reliable by control. Computer can memorize or print all required running records and proportion datum.
·Control room is equipped with air-conditioner, providing operator comfortable working environment.
Note: High-voltage cable and transformer shall be at least 30m away from control room, avoiding interfering computer.
9. Computer-controlled system (Part 9)
9.1 Central control room
Dimension: L 5000mm, W 2300mm
Quantity: 1pc
9.2 Air conditioner
Type: 1.5P
Quantity: 1pc
9.3 Industrial computer
Type: Industrial control/ PLC
Control: Manual/ auto
Quantity of displayer: 1pc
Quantity of printer: 1pc
9.4 Computer control cabinet
Type: Lyre
Quantity: 1pc
Fittings: Electric components, receiver of control signals and various instruments
9.5 Heavy-current control cabinet
Type: Standing
Quantity: 1set
Fittings: Electric components, receiver of control signals and various instruments
十 Product storage
Structure:single-drum bin with inclined ceiling, conical bin body with external heat conductive oil and asbestos heat-preservation layer under colored steel board
Volume: 30T
Electric-heating power for discharge door: 2KW×2
Quantity: 1set
十一 Mastic feeder
Capacity: 0,45м3
Bucket Capacity: 0,50м3
Measure time: 0-10s
Supply time: 0-10s
Feeder: 0-15kg/time
Power: 10.5kw
Quantity: 1set
Component Power Distribution Table
No
|
Name
|
Power
|
Qty.
|
Remark
|
Part 1. Cold-aggregate supply system
|
1.1
|
Cold material feeder
|
2.2kw
|
4
|
|
1.2
|
Aggregate belt machine
|
4kw
|
1
|
|
1.3
|
Feed belt machine
|
4kw
|
1
|
|
Total power: 16.8kw
|
Part 2. Baking& heating& lifting system
|
2.1
|
Drying drum
|
7.5kw
|
2
|
|
2.2
|
Main burner
|
18.5kw
|
1
|
|
2.3
|
Oil pump motor of burner
|
1.5kw
|
1
|
|
2.4
|
Air compressor
|
7.5kw
|
1
|
|
2.5
|
Hot-material elevator
|
7.5kw
|
1
|
|
Total power: 50kw
|
Part 3. Screening& metering system
|
3.1
|
Vibration screen
|
5.5kw
|
1
|
|
Total power: 5.5kw
|
Part 4. Storage& supply system for mineral and recovered powder
|
4.1
|
Spiral feeder
|
3kw
|
1
|
|
4.3
|
Powder elevator
|
5.5kw
|
1
|
|
4.4
|
discharging valve
|
1.1kw
|
1
|
|
4.5
|
Mineral powder metering spiral conveyor
|
3kw
|
1
|
|
Total power: 22.2kw
|
Part 5. Mixing system
|
5.1
|
Mixer
|
30kw
|
1
|
|
Total power: 30kw
|
Part 6. Dedusting system
|
6.1
|
Star-type discharge valve
|
1.1kw
|
2
|
|
6.2
|
Bag filter dust
|
3kw
|
1
|
|
6.2
|
Main draught fan
|
37kw
|
1
|
|
Total power: 42.2kw
|
Part 7. Heat conductive oil heating system
|
7.1
|
Boiler burner
|
0.45kw
|
1
|
|
7.2
|
Heat conductive oil circulating pump
|
7.5kw
|
1
|
|
7.3
|
Heat conductive oil filling pump
|
1.1kw
|
1
|
|
7.4
|
Bitumen delivery pump
|
5.5kw
|
2
|
|
Total power: 20.05kw
|
Part 8. Gas circuit control system
|
8.1
|
Air compressor
|
7.5kw
|
2
|
|
Total power: 15kw
|
Part 9. Computer-controlled system
|
9.1
|
Central control room
|
3kw
|
1
|
Including air conditioner
|
Total power: 3kw
|
Part 10. Ready product storage
|
10.1
|
Heat preservation
|
2kw
|
2
|
|
Total power: 4kw
|
Part 11. Mastic feeder
|
|
Total power: 10.5kw
|
Power of total equipment: 219.25kw
|
Made of Main Components
No
|
Name
|
Place
|
Brand
|
Original
|
1
|
Main burner
|
Drying drum
|
EBICO
|
Italy
|
2
|
Boil Burner(oil and gas)
|
Heat conductive oil furnace
|
RELLO
|
Italy
|
3
|
Air compressor
|
Gas circuit system
|
SCR
|
Taiwan
|
4
|
Cylinder
|
Pneumatic system
|
Air TAC
|
Taiwan
|
5
|
Solenoid valve
|
Pneumatic system
|
Air TAC
|
Taiwan
|
6
|
Electronic unit
|
Heavy-current control cabinet
|
ABB/others
|
Switzerland
|
7
|
Industrial control
|
Computer control system
|
ADVANTECH
|
Taiwan
|
8
|
PLC
|
Computer control system
|
SIEMENS
|
Germany
|
9
|
Weighing sensor
|
Weighing system
|
PFT
|
New zealand
|
10
|
Transducer
|
Cold feed machine
|
TAIAN
|
Taiwan
|
11
|
Level indication
|
Hot aggregate bin
|
Fine
|
Taiwan
|
12
|
Bag filter
|
Bag dust system
|
Nomex
|
America
|
13
|
Bearing
|
Drying drum
|
Timken
|
America
|
14
|
Bearing
|
aggregate elevator
|
Timken
|
America
|
15
|
Bearing
|
Mixing tank
|
Timken
|
America
|
16
|
Bearing
|
Vibration screen
|
Timken
|
America
|
17
|
Electric motor
Reductor
|
Cold feed machine
|
GUOTAI
|
China
|
18
|
Electric motor
Reductor
|
1#aggregate conveyor
|
GUOTAI
|
China
|
19
|
Electric motor
Reductor
|
2#feed delivery machine
|
GUOTAI
|
China
|
20
|
Electric motor
Reductor
|
Drying drum
|
GUOTAI
|
China
|
21
|
Electric motor
Reductor
|
Hot-aggregate elevator
|
GUOTAI
|
China
|
22
|
Electric motor
Reductor
|
Mineral powder elevator
|
GUOTAI
|
China
|
23
|
Electric motor
Reductor
|
Mixing tank
|
GUOTAI
|
China
|
SPARE PARTS LIST
No
|
Name
|
Qty
|
Place
|
1
|
Bearing
|
1pc
|
Feed belt machine/ spiral conveyor
|
2
|
Bearing
|
1pc
|
Aggregate/ supply belt conveyor
|
3
|
Bearing
|
1pc
|
Screw shaft of mineral powder elevator
|
4
|
Bearing
|
1pc
|
Line shaft of mineral powder elevator
|
5
|
Bearing
|
1pc
|
Screw shaft of hot-material elevator
|
6
|
Elevator anchor-chain
|
2m
|
Hot-stone elevator
|
7
|
Elevator anchor-chain
|
2m
|
Mineral powder elevator
|
8
|
Lifting bucket
|
3pcs
|
Hot-stone elevator
|
9
|
Lifting bucket
|
3pcs
|
Mineral powder elevator
|
10
|
Electromagnetic
diverter valve
|
2pcs
|
Pneumatic control box
|
11
|
Electromagnetic
diverter valve
|
2pcs
|
Bag filter dust system
|
12
|
Pulse
|
2pcs
|
Bag filter dust system
|
13
|
Seal ring
|
1set
|
Hot-aggregate bin
|
14
|
Seal ring
|
1set
|
Metering system
|
15
|
Seal ring
|
1set
|
Dust system
|
16
|
Air tube
|
10m
|
Pneumatic system
|
17
|
Air-tube joint
|
2pcs
|
Pneumatic system
|
18
|
Control button
|
2pcs
|
Electric control cabinet
|
19
|
thermal resistance
|
1pc
|
Temperature detector
|
20
|
V-belt
|
3pcs
|
Vibration screen
|
21
|
Blade
|
6sheets
|
Mixing tank
|
22
|
Paddle arm
|
2pcs
|
Mixing tank
|
23
|
Paddle arm
|
2pcs
|
Mixing tank
|
24
|
bolt
|
10sets
|
Mixing tank
|
25
|
Screen
|
1set
|
Vibration screen
|
Tools list
No.
|
Name
|
Type
|
Qty.
|
Unit
|
Remark
|
1
|
Hammer
|
2pounds
|
1
|
Pc
|
|
2
|
Pliers
|
|
1
|
Pc
|
|
3
|
Internal circlip pliers
|
|
1
|
Pc
|
|
4
|
External circlip pliers
|
|
1
|
Pc
|
|
5
|
Spanner wrench
|
12”
|
1
|
Pc
|
|
6
|
Spanner wrench
|
10”
|
1
|
Pc
|
|
7
|
Screwdriver
|
Straight
|
1
|
Pc
|
|
8
|
Screwdriver
|
Cross
|
1
|
Pc
|
|
9
|
Tubing pliers
|
|
1
|
Pc
|
|
10
|
Internal hexagon spanner
|
|
1
|
Set
|
|
11
|
Ring spanner
|
|
1
|
Set
|
|
12
|
Prize
|
|
2
|
Pc
|
|